NMC AutoSpec

NMC Decorative Mouldings

Company Profile

NMC is an internationally leading company active in the development, production and marketing of synthetic foams.

Founded in 1950, NMC develops, manufactures and markets synthetic foam products. Our 1200 worldwide associates strive to develop innovative, reliable, and high-quality products supported by a complete service package.

NMC Group realizes an annual turnover of 180 million Euros.

NMC Group realizes an annual turnover of 180 million Euros.

FAQ's

WHO IS NMC?

We are the world leader in decorative mouldings. All styrene and polyurethane products are manufactured in Belgium

HOW LONG WILL NMC MOULDINGS LAST?

Indefinitely under normal conditions. Even jn humid conditions the NMC mouldings cannot be damaged by water (i.e. bathrooms,)

HOW STRONG IS THE PRODUCT?

Both the Polyurethane and the styrene are very strong and durable. They will not chip or break if dropped. Cuts or bad dents can be filled with the adhesive and lightly sanded (120g sandpaper). The styrene is not as hard as the Polyurethane, and therefore cannot he used for dado rails, low picture rails and skirting boards.

IS THE PRODUCT ENVIRONMENTALLY FRIENDLY?

Yes. NMC products are both Solvent free and CFC free. They can safely be used in infant or children’s rooms.

HOW IS THE PRODUCT AFFECTED BY HEAT?

Direct heat, too close to the mouldings, can damage the surface. (Styrene products are more sensitive to heat than the Polyurethane products.). The larger cornices can however be used for concealed lighting, using either low voltage or fluorescent lights, with approximately 6cm clearance

IS THERE A LOT OF WASTAGE?

No, very little. Approx. 5% of the total product required, rounded up to the nearest 2m length.

ARE THE NMC PRODUCTS EXPENSIVE?

The styrene is cheaper or equivalent to any of it’s competitors. The Polyurethane range is more expensive due to the sophisticated technology that goes into the product, but due to the substantial savings on the indirect costs, such as installation, wastage or breakage, the product works out comparatively cost effective

CUTTING

Use a fine toothed panel saw or veneer saw This will give a clean edge without damaging the product. Ask your hardware specialist for assistance in choosing the saw. Do not cut with a knife or hot wire. (There are simple directions on all the packaging & in the brochures). The NMC mitre box takes all the guesswork out of cutting, especially the angles required for corners. Ask your dealer about the complete NMC tool kit, which is available for hire or to purchase.

ADHESIVE

WHAT ADHESIVE SHOULD I USE?

We recommend NMC "2 in 1" adhesive product, specifically designed for use with the NMC mouldings, which is both an adhesive and filler.

WHAT IS THE ADHESION TIME?

Living the NMC adhesive, the moulding will bond instantly Pane/pins should be used to support joints whilst adhesive dries. If the mouldings are not positioned correctly you have approximately 10 minutes to correct or remove it before adhesion sets.

WHAT TYPE OF SURFACE CAN THE NMC ADHESIVE BE APPLIED TO?

The adhesive can be used on most surfaces including tiles, steel, glass, wood and plastered surfaces. The latter should be primed prior to installation

WHAT IS THE COMPLETE DRYING TIME?

The NMC adhesive should completely dry/set within 24 hours. (Drying time is subject to weather conditions or humidity)

WHAT IS THE BRIDGING AND FILLING CAPACITY?

DThe NMC Adhesive / Filler have a 6mm bridging capacity. The adhesive can be sanded to achieve a smooth finish.

NB. When joining profiles, always leave a 2-3 mm gap, filled with adhesive. This acts as an expansion joint and prevents cracking on joints.

WILL IT STAIN CARPETS OR FABRIC?

NMC adhesive is water based and therefore easy to clean. Simply wipe clean immediately and it won’t leave a stain

WHAT QUANTITYOF ADHESIVE WILL I NEED TO BUY?

Per 5kg Tub:Small profile-60m
Medium profile-40m
Large profile-30m

The above are guidelines only, and depend on the finish of walls i.e. rough plaster or bricks would require more adhesive as would skew walls and ceilings. The tubs of adhesive are more economical as any excess adhesive can be recycled. The cartridge with cone nozzle is perfect for easy fillings and finishing, especially in corners

PAINTING

CAN I LEAVE THE NMC MOULDINGS UNPAINTED?

This is not advised, as the mouldings would yellow over time.

WHAT PAINT CAN I USE ON THE NMC MOULDINGS?

Polyurethane: Already have factory primer; so any paint or paint effect can be used on the mouldings. Styrene: Any water based or acrylic paint can be used directly on the product. A contractor PVA or primer would he required before applying any enamel or solvent based paint.

CAN I PAINT THE NMC ADHESIVE?

Yes, with any paint.

WHAT ABOUT SPECIAL PAINT EFFECTS?

Almost any special paint effect can be applied to the mouldings

WHO CAN INSTALL THE PRODUCT?

The product is suitable for DIY application. For professional installation, contact NMC Johannesburg for recommended fitters.